xfinity flex stopped working

Actually use a wired connection if available. Voice control isnt working.

Xfinity Flex Is Not Working Complete Troubleshooting Guide Streamdiag

Wait until the LEDs on the front of the gateway flash off.

. Pressing the xfinity button on your Xfinity Voice Remote. Select Start Troubleshooting to begin your modem restart. Its extremely frustrating when your Xfinity remote is unresponsive especially when youre stuck on one channel.

Heres how to reset the Xfinity XR 11 Remote device to fix Xfinity remote not working and get it back to normal mode. These include backup programs social networks collaboration tools etc. Check to see if there are any other devices on your home network using bandwidth.

Locate the reset button on the back of your Xfinity gateway. On the Services tab tap the Troubleshoot button in the Flex section. Dust can also be an issue because it can clog the insides and disrupt the internal connections resulting in your remote not changing channels but working on volume.

As the title says we just got a free bit of hardware from Xfinity wed like to use. The top 7 reasons why your Xfinity remote isnt working include. When powering off the Flex box I also unplugged the HDMI cable.

If Netflix is not working on Xfinity reset the app reset your network check that you are connected to a network confirm that all wires are securely inserted on both TV and Xfinity box try playing another title and check to make sure that you have an Xfinity box that is compatible with the app. As noted the Flex box is hardwired. Peacock not working on flex - XFinity.

The TV room is in the opposite corner of the house and because of this the installers suggestion was to switch our X1. Each of these common issues may be a contributor to stopping your Xfinity remote from working properly. Comcasts new Xfinity Flex streaming platform lets its internet-only customers pay 5 a month for a 4K HDR-ready connected box that will allow them to watch Netflix Amazon Prime and other.

Depending on your gateway model it will be located near the top of the router or below the coaxial cable connector. Xfinity Flex not working possibly due to pihole. To factory reset the remote press the A and D buttons at the same time until the light changes to green.

Comcast Customer Service is here to provide Help and Support for your Xfinity Internet TV Voice Home and other services. System is experiencing a bug. I can ping the IP address successfully.

It is common for some problems to be reported throughout the day. If your Xfinity remote is not working remove the batteries and hold down the power button on the remote for 30 seconds. Pressing the right arrow to go to the Apps menu.

After this the Yikes 22010 message is again displayed. This chart shows a view of problem reports submitted in the past 24 hours compared to the typical volume of reports by time of day. Xfinity Flex outages reported in the last 24 hours.

Then there is a screen displayed that says the device has been restarted and to press any key on the remote to continue. As per the user reports the Xfinity remote stops working out of nowhere and no matter what key is pressed theres no response. Press the POWER and MENU buttons simultaneously Press the UP and DOWN buttons on the remote simultaneously Select Restore Defaults.

You can also go to the Devices tab. After doing these things I powered the Flex back on while the Flex was showing the initial Welcome screen take a battery out of the remote and put it right back press Voice button numerous times and I finally got to the next setup menu. I have created an IP reservation in my DHCP sever section of my router.

Close any background programs that might be using bandwidth. It is possible that your Xfinity Remote will stop working as a result. Hold down the reset button for 30 seconds.

You should press and hold the button labeled Setup When you press and hold it the red-color light will turn green. Just recently moved into a new home and transferred Xfinity service with it. Flex box connection issues.

How to reset your Xfinity gateway. Troubleshooting Your Xfinity Flex Service Open the Xfinity My Account app on your mobile device and sign in with your Xfinity ID and password. Once you see that just press 9 8 1.

Not an Xfinity remote. Press Ok if any prompts appear. The cable line was installed entering the house near our home office with the Xfinity router placed there as well.

Maybe your kids are streaming something. Move closer to the wireless router. Downdetector only reports an incident when the number of problem reports is significantly higher.

The reason this happens can vary as there are different things that can come into play when your remote stops working including dead batteries programming of the remote and more. Now go out of peacock by clicking guide button on the remote. LED signal is obstructed.

If something spills on it the buttons can become stuck or the circuitry inside can be damaged. Xfinity flex box users were facing problems. If that code doesnt work you should try 9 9 1.

Next press the buttons 9 8 and 1. If you have Xfinity and Netflix stops working what can be done. The problem is when we try to connect it to the internet it gets an ENT-22010 error saying Yikes that didnt work.

Too many remotes and TV boxes. I powered off and on again. Apps not showing remote not working stuck on account screen.

Xfinity Flex Down Current Problems And Outages Downdetector